Product Description
High speed transmission shaft flange serpentine shaft snake spring grid flexible coupling
Description:
JS grid coupling vibration, JS grid coupling and long service life. JS grid coupling under high load range, JS grid coupling
starting safety, high transmission efficiency, reliable operation.
Features:
1.The serpentine spring as the elastic element, the elastic strong at the same time, greatly improves the grid coupling torque, widely used in heavy machinery and general machinery.The serpentine spring special technology department, has long service life, allowing higher speed, has good ability to compensate in the axial, radial and angle
2.High transmission efficiency, start safety. Transmission efficiency of up to 99.47%, short-time overload capacity is 2 times the rated torque, operation safety.
3.Simple structure, convenient assembly and disassembly, long service life
4.Damping effect is good to avoid the resonance.
Advantages:
1. Good vibration reduction and long service life
The coupling is axially embedded in the 2 halves by more than 36% of the serpentine spring. The trapezoidal cross-section serpentine spring piece is made of high-quality spring steel, which has undergone strict heat treatment and is specially processed. It has good mechanical properties, so that the service life of the coupling is much longer than that of non-metal elastic element Column pin coupling, nylon rod pin coupling) greatly increased.
2. Wide range of variable loads and safe starting
The tooth surfaces where the 2 half-couplings contact the reed are arc-shaped. When the transmission torque increases, the spring leaf will deform along the tooth arc surface, so that the force points of the 2 half-couplings acting on the reed are close. The contact point between the reed and the tooth surface, that is, the change of the torque, changes with the magnitude of the transmitted torque, and its transmission characteristics are variable stiffness. Therefore, it has a greater load variation than ordinary elastic couplings. The buffer effect produced when the transmission force makes the reed deform along the tooth arc, especially when the machine is started or when a strong impact load occurs, can protect the safety of the supporting parts to a certain extent.
3. High transmission efficiency and reliable operation
The transmission efficiency of the coupling has been determined to reach 99.47%, and its short-term overload capacity is twice the rated torque, and the operation is safe and reliable.
4. Low noise and good lubrication
The aluminum alloy casing protects the spring from being thrown out during operation, and the casing is filled with butter, which not only ensures good lubrication, but also eliminates the noise when the reeds engage by being absorbed by the grease damping.
5. Simple structure, easy assembly and disassembly
The whole machine has few parts, small size, and light weight. The spring piece designed as a trapezoidal cross-section fits the trapezoidal tooth groove very conveniently and tightly, so that the assembly, disassembly and maintenance are easier than ordinary couplings.
6. Large installation deviation is allowed
Since the spring piece is in point contact with the arc surface of the tooth, the coupling can obtain greater flexibility. It can be installed to work normally with radial, angular and axial deviations at the same time.
Packing & Delivery:
Tight packaging to protect the product from damage. Support a variety of payment and transportation methods.
About us:
HangZhou CHINAMFG machinery technology Co., Ltd is an industry transmission solutions manufacuturer and service provider.
We offer 1 stop solution for power transmission products for different factories, such as chemicals, energy, material handling, environmental, extraction, pulp and paper, steel and metal, food and beverage, and construction industries.
We supply: Customised gears, Small gearmotors, Industrial gearboxes, Motors, Brand product sourcing.
Our industrial Gear, Gearbox, gearmotor and motor are sold to more than 30 countries. High quality, good price, in time response and sincere service are our value and promises. We aim at making happy cooperation with our customers, bring them reliable and comfortable service. /* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
Are There Specific Safety Precautions to Consider When Working with Motor Couplings?
Yes, there are several safety precautions that should be taken into consideration when working with motor couplings:
- Lockout-Tagout Procedures: Before performing any maintenance or installation work on motor couplings, it is essential to follow proper lockout-tagout procedures. This involves disconnecting the power source and placing a lock and tag on the disconnect switch to prevent accidental energization of the equipment.
- Proper Personal Protective Equipment (PPE): When working with motor couplings, personnel should wear appropriate personal protective equipment, including safety glasses, gloves, and other necessary gear to protect against potential hazards and injuries.
- Securely Support Equipment: Ensure that all equipment connected to the motor coupling is securely supported to prevent unexpected movement or collapse during maintenance or operation.
- Avoid Excessive Misalignment: While motor couplings can compensate for misalignment to some extent, it is crucial to avoid excessive misalignment beyond the coupling’s specified limits to prevent premature wear and potential failure.
- Follow Manufacturer’s Instructions: Always adhere to the manufacturer’s guidelines, recommendations, and installation procedures when working with motor couplings. Improper installation or usage can lead to performance issues and safety hazards.
- Regular Inspection: Conduct regular inspections of motor couplings to identify any signs of wear, damage, or misalignment. Address any issues promptly to maintain safe and reliable operation.
- Stay Informed: Ensure that personnel working with motor couplings are properly trained and informed about potential risks and safety procedures.
- Safe Handling of Equipment: Use appropriate lifting and handling equipment when moving or installing motor couplings to prevent injuries and damage to the equipment.
- Environmental Considerations: Consider the environmental conditions in which the motor coupling will operate and choose materials and coatings that can withstand the specific environment to ensure safe and reliable performance.
By following these safety precautions, individuals can mitigate risks associated with working with motor couplings and contribute to a safe working environment for all personnel involved in the installation, maintenance, and operation of the equipment.
Can motor couplings handle reversing loads and shock loads effectively?
Motor couplings are designed to handle various types of loads, including reversing loads and shock loads, effectively. Let’s explore their capabilities in dealing with these load conditions:
1. Reversing Loads
Reversing loads occur when the direction of the transmitted torque alternates periodically. Motor couplings, especially flexible couplings and universal couplings (Hooke’s joints), are well-suited for handling reversing loads. These couplings can accommodate angular misalignments between the motor and driven load, allowing for smooth torque transmission even during direction changes. Properly aligned and maintained couplings can endure frequent reversals without significant wear or fatigue.
2. Shock Loads
Shock loads refer to sudden and intense forces that exceed the typical operating conditions. These loads can occur due to abrupt starts, stops, or impacts in the system. Motor couplings, particularly those with some level of flexibility, possess inherent shock-absorbing properties. Flexible couplings can dampen the impact of sudden loads, reducing the stress on connected components and preventing damage. Rigid couplings are less forgiving to shock loads but may still be suitable for certain applications where the impact is within their load-bearing capacity.
However, it’s essential to consider the specific application requirements and choose the appropriate coupling type based on the expected load conditions. Factors such as the magnitude and frequency of reversing and shock loads, system dynamics, and the overall design should be considered when selecting a motor coupling. Additionally, regular maintenance and inspection play a crucial role in ensuring that the couplings continue to perform effectively under challenging load conditions.
“`
Are Grid Couplings Suitable for High Torque and Misalignment Conditions?
Yes, grid couplings are well-suited for high torque and misalignment conditions in industrial applications. They offer several features that make them an excellent choice for such conditions:
- High Torque Capacity: Grid couplings are designed to handle high torque loads, making them suitable for heavy-duty industrial machinery and equipment.
- Misalignment Tolerance: Grid couplings can accommodate both angular and radial misalignments between the connected shafts. This ability to tolerate misalignments is crucial in industrial settings where perfect alignment may not always be possible.
- Vibration Damping: The serrated grid element in grid couplings acts as a vibration damper, absorbing shocks and vibrations that can occur during high-torque operation. This feature helps in reducing noise levels and ensuring smoother machinery performance.
- Shock Load Absorption: Grid couplings are specifically designed to absorb shock loads, which are common in industrial environments. This capability protects the connected equipment from sudden overloads and prevents damage to the machinery.
- Torsional Flexibility: The flexible grid structure of the coupling provides torsional flexibility, allowing it to compensate for torsional vibrations and torque spikes that often occur in high-torque conditions.
Grid couplings are commonly used in applications where high torque is required, such as in pumps, compressors, mixers, and other heavy machinery. Additionally, their ability to handle misalignments makes them suitable for various industrial settings where precise alignment may be challenging.
When properly installed and maintained, grid couplings provide reliable performance in high-torque and misalignment conditions, contributing to smoother machinery operation and extended equipment life.
editor by CX 2024-05-06